6 x Everbuild Decorators Caulk 125 Everflex 1 Hour C3 White +1 Free Caulking Gun

Description

6 x Everbuild 125 One Hour Caulk C3 - White
+ 1 FREE Caulking Gun
Everflex one hour caulk is a fast drying flexible decorators filler and sealant which can be overpainted with all paint types, or covered over with wallpaper. No sanding down is required.
Spec
Fast drying flexible decorators filler and sealant
Remains permanently flexible
Can be overpainted with most paint types or covered over with wall paper
No sanding down required
Easy water clean up.
Excellent slump resistance.
Certified to the harmonized European standard EN15651 for façade use internally in compliance with the Construction Product Regulation.
Application
Cut the tip of the cartridge taking care not to damage the thread. Apply nozzle and cut cleanly at an angle of 45’ with an opening slightly larger than the gap to be sealed. Apply using a standard sealant gun. Best results will be obtained by keeping an even pressure on the gun Trigger and keeping the gun at a constant angle to the surface being sealed. Smooth down within 20 minutes of application using a wetted spatula, piece of wood or wetted finger. Care should be taken at this point not to saturate the surface as this will delay drying. Any excess sealant etc., can be removed using a sponge and warm water. Can be overpainted after @ 1 hour.
Surface Preparation
All surfaces must be clean, dry and dust free. All loose or flaking surface coatings, and old sealant and mastic joints, should be removed before application. Highly porous substrates such as new plaster should first be primed with a dilution of Caulk with water at a ratio of 1:2. Can be applied to slightly damp surfaces.
Areas For Use
For sealing and filling cracks and gaps prior to decorating.
For use around skirting boards, ceiling cornices, window and door frames, stair treads and risings and fixtures adjoining walls.
Can be used to fill damage plaster.
Size
300ml
Specific Data
Form
Ready to use thixotropic paste
Specific Gravity
1.62 – 1.70
Elongation at Break (%)
>100% to ISO8339
Hardness (Shore A)
Approximately 50
Tack Free Time
15 to 60 mins, dependent on thickness, ambient temperature and humidity
Full Cure
3 to 5 days, dependent on thickness, ambient temperature and humidity
Solids Content
80-84%
Slump Resistance
No slump to ISO 7390
Application Temp. Range
+4°C to +40°C
Service Temp. Range
-15°C to +75°C
Chemical Resistance
Dilute Acids - Fair Dilute Alkaline - Fair
Aliphatic Hydrocarbons - Fair AromaticHydrocarbons - Poor
Movement Accommodation
Low to medium (+/- 5%)
Durability
Up to 10 years when used as recommended
Shelf Life
Up to 36 months when stored in unopened cartridges under cool dry conditions.
AVOID FROST
Compatibility
Can be used in contact with most building and decorating materials but should not be used against bituminous materials.
Limitations
Should not be used in conditions of continuous immersion, below ground level, in areas of high abrasion (e.g. floor joints).
Cut the tip of the cartridge taking care not to damage the thread. Apply nozzle and cut cleanly at an angle of 45’ with an opening slightly larger than the gap to be sealed. Apply using a standard sealant gun. Best results will be obtained by keeping an even pressure on the gun Trigger and keeping the gun at a constant angle to the surface being sealed. Smooth down within 20 minutes of application using a wetted spatula, piece of wood or wetted finger. Care should be taken at this point not to saturate the surface as this will delay drying. Any excess sealant etc., can be removed using a sponge and warm water. Can be overpainted after @ 1 hour. All surfaces must be clean, dry and dust free. All loose or flaking surface coatings, and old sealant and mastic joints, should be removed before a